Fracture Toughness and Strength: Cracks Change the Material Question
Keep a crack-sensitive material question separate from an uncracked tensile-strength comparison.
Read Full Article →Technical Knowledge Center
Machine Guide Library — Page 9
Practical guides for selecting, planning, operating and maintaining pharmaceutical manufacturing and packaging machinery.
Latest articles
Technical Insights from Our Machinery Team
Practical guides to washing, filling, capping, labeling and machine planning. Each card has a distinct Library date; actual publication and revision dates remain inside the article.
Machine guide library
Further Machine Guides
Browse guides by their distinct Library date. These collection labels are separate from actual publication and revision dates shown inside each article.
Polymer Creep: A Constant Load Can Produce Changing Deflection
Evaluate a polymer part's time-dependent deformation under a sustained load.
Read Full Article →
Stress Relaxation: A Fixed Deflection Can Produce a Changing Force
Assess whether a held deformation preserves the force needed by a polymer assembly over time.
Read Full Article →
Filled-Polymer Thermal Expansion: Check Direction as Well as the Coefficient
Preserve direction when using expansion coefficients for a filled-polymer part.
Read Full Article →
Environmental Stress Cracking of Plastics: Chemical and Mechanical Conditions Interact
Review stressed-plastic chemical exposure without treating an unstressed immersion result as the full requirement.
Read Full Article →
UV Weathering of Plastics: An Indoor Material Claim Does Not Set Outdoor Life
Ask which weathering evidence represents an exposed plastic part's actual light, moisture and temperature duty.
Read Full Article →
UL 94 Classification and Service Temperature: Separate Flammability from Heat Capability
Read a UL94 material classification separately from thermal-use and assembled-equipment evidence.
Read Full Article →
Dielectric Strength and Volume Resistivity: Different Insulation Properties
Separate resistance to breakdown from resistivity when reviewing an insulating plastic.
Read Full Article →
Polymer Friction and Wear: Keep Pressure and Sliding Speed in the Application
Keep contact pressure and sliding speed with a polymer wear comparison.
Read Full Article →
Heat-Deflection Temperature and Continuous Service: Do Not Exchange the Labels
Keep heat-deflection temperature separate from continuous-use information for a plastic component.
Read Full Article →
From Witnessed FAT to Dispatch: Reconcile the Final Machine Condition
Reconcile post-FAT changes with the witnessed configuration before dispatch, keeping transport arrangements, evidence applicability and open items distinct.
Read Full Article →
Low-Temperature Elastomer Behavior: Compare Recovery with a Generic Temperature Range
Identify the low-temperature property and actual motion requirement behind an elastomer recommendation.
Read Full Article →
Elastomer Gas Permeation: A Sound Seal Can Still Transmit Gas Through the Material
Distinguish gas passing through an elastomer material from gas passing around a sealing interface.
Read Full Article →
Static and Dynamic Seals: Motion Changes the Friction and Wear Requirements
Keep relative motion in the seal-duty definition rather than reusing a static-joint assumption.
Read Full Article →
O-Ring Groove Fill: Keep Seal Volume and Available Space in the Same Review
Put seal volume and available groove space on a defined common basis.
Read Full Article →
Fiber Orientation in Plastic Parts: Directional Properties Belong on the Drawing
Preserve load direction and fiber orientation when comparing properties of a reinforced plastic part.
Read Full Article →
Hard Coatings and Adhesion: A Surface Hardness Claim Does Not Prove Bond Integrity
Keep coating hardness, adhesion and substrate compatibility as separate evidence in a surface proposal.
Read Full Article →
Adhesive Joints in Shear and Peel: Geometry Changes the Loading Question
Compare adhesive evidence against the actual shear or peel loading of the proposed joint.
Read Full Article →
Adhesive Fixture Time and Full Cure: Define When the Joint Must Carry Load
Distinguish an adhesive joint's handling stage from its stated full-cure condition.
Read Full Article →
Dissimilar-Material Adhesive Joints: Include Differential Expansion in the Duty
Keep differential expansion in the duty of an adhesive joint between different materials.
Read Full Article →
Iron Contamination on Stainless: Separate Surface Residue from Base-Material Corrosion
Distinguish deposited iron contamination from base-material corrosion when investigating stainless staining.
Read Full Article →
Heat and Temperature: Put Mass and Heat Capacity into the Comparison
Temperature alone does not describe the energy needed to heat a batch. Name its mass, material and temperature change first.
Read Full Article →
Sensible and Latent Heat: Identify the Phase Change
A temperature plateau during a phase change can still consume or release a substantial amount of energy.
Read Full Article →
Overall Heat Transfer Is Not Material Conductivity
A wall material’s conductivity and an exchanger’s overall coefficient describe different parts of the thermal problem.
Read Full Article →Blog overview · Latest articles · Machine guide library
Choosing the Right Machine
Application-based guidance for selecting equipment according to product, container, closure and output.
Planning a Packaging Line
Practical considerations for connecting washing, filling, capping, labeling and conveying machinery.
Operation & Maintenance
Useful information for changeovers, cleaning, preventive maintenance and dependable machine performance.
Need Guidance Before Selecting a Machine?
Share your product, container, closure, required output and process details with our engineering team.